Preamplifiers
-
The L-10000 OTL/OCL (Output Transformer-Less/Output Capacitor-Less) is a triple gain stage, remote controlled, line-stage preamplifier, without transformers or capacitors in its single-ended signal path.
- OTL, OCL Direct Coupled preamplifier
- Two SEPP 300Bs output
- True Dual Mono design
- 61-step Silver Contact Constant Impedance attenuator
-
The L-9000 OTL/OCL (Output Transformer-Less/Output Capacitor-Less) is a triple gain stage, remote controlled, line-stage preamplifier, without transformers or capacitors in its single-ended signal path.
- OTL, OCL Direct Coupled preamplifier
- Two SEPP 6080s output
- True Dual Mono design
- 61-step Silver Contact Constant Impedance attenuator
-
The L-8500 OTL/OCL (Output Transformer-Less/Output Capacitor-Less) is a triple gain stage, remote controlled, line-stage preamplifier, without transformers or capacitors in its single-ended signal path.
- OTL, OCL Direct Coupled preamplifier
- Two SEPP 12B4s output
- True Dual Mono design
- 41-step Silver Contact Constant Impedance attenuator
-
Immerse yourself in the original recorded space. The L-7000 is a single gain stage, transformer coupled, remote controlled line stage pre-amplifier. It uses the DHT 300B as a voltage regulator.
- DHT 300B as a series voltage regulator
- Single gain stage
- True Dual Mono design
- 41-step Silver Contact Constant Impedance attenuator
-
The Allnic L-8000 DHT preamplifier is the improved successor to the L-5000 DHT, which was the world's first commercially produced, pure DHT preamplifier.
- All signal circuits with DHT (Direct Heated Triode)
- Line output transformer coupling
- No negative feedback design
- Advanced tube technology voltage regulation
- 61-step Silver Contact Constant Impedance attenuator
-
Allnic's new preamplifier L-6500 features:
- Single gain stage
- Pure Class A operation
- Ultra-low output impedance
- Advanced tube technology voltage regulation
- Precision attenuator volume control
- RCA and XLR inputs and outputs
Power Amplifiers
-
The M-3000 mk2 is one of Allnic’s famous 3000 series, world leading components with revelatory clarity, incredible dynamics and drive, and standard setting low noise and distortion. One of the first amplifiers to use the new KT-150 power tube, the M-3000 mk2 offers massive, stable, resolute power in the proverbial velvet glove. With “on-the-fly” pentode/triode switching, the M-3000 mk2 delivers 200 watts into 8 ohms in pentode mode, and more than 90 watts of “SET like” power output in triode mode. In either mode, the M-3000 mk2s virtues will amaze with power, grace, finesse, lifelike dynamics and amazing micro-detail.
- 200 watts of high power output in pentode mode
- More than 90 watts of “SET like” power output in triode mode
- Analogue power tube current monitoring meters
- Exceptionally easy bias controls
- Soft-start Circuitry
-
The M-5000 TITAN is one of Allnic’s world leading components, with revelatory clarity, incredible dynamics and drive, and standard setting low noise and distortion. Using 8 KT-150 power tubes, the M-5000 TITAN offers massive, stable, resolute power in the proverbial velvet glove. The M-5000 TITAN delivers 400 watts into 8 ohms in pentode mode and 125 watts in pure triode.
- 400 watts (pentode) or 125 watts (triode) of high-power output
- Powerful Driving Circuitry
- Full Engagement” Output Transformers
- Large Nickel/FeSi Core Output Transformers
- Soft-start Circuitry
-
The Allnic Audio A-2000 25th Anniversary is a 100 watt (pentode) push-pull, stereo power amplifier. Like its integrated amplifier brother, the T-2000, the A-2000 25th Anniversary is pentode/triode switchable “on-the-fly”, providing more than 50 watts in SET sounding triode mode. The A-2000 25th Anniversary offers stable, resolute power in the proverbial velvet glove, along with amazing, revelatory clarity, incredible dynamics and drive, articulate and powerful bass, and standard setting low noise and distortion.
- 100 watts of high power output in pentode mode
- More than 50 watts of “SET like” power output in triode mode
- "On-the-fly" pentode/triode switching
- Analogue power tube current monitoring meters
- Exceptionally easy bias controls
- Soft-start Circuitry
-
The M-2500 monoblock power amplifiers are Allnic Audio’s top of the line, power tube flexible, pushpull monoblock power amplifier model. Like all Allnic Audio products, the M-2500s have Permalloy (iron and nickel alloy) for their transformer cores. Allnic is grateful to Mr. G.W. Elmen of Western Electric for inventing Permalloy for transformer core use, and in so doing, providing an enormous service to recorded music listeners everywhere.
- 100 watts of high power output in pentode mode
- More than 30 watts of “SET like” power output in triode mode
- Analogue power tube current monitoring meters
- Exceptionally easy bias controls
- Soft-start Circuitry
-
A-311 M series are all monoblock single-ended power amplifiers. All of them use DHT (direct heated triode) power tubes, such as 300B, PX25, or AD1 as output vacuum tubes, with selection of the output tube type by customer at time of order.
- Pure Class A power stage : 10W(300B), 6W(PX25), 4W(AD1)
- Allnic's DHT technology
- Analogue power tube current monitoring meters
- Exceptionally easy bias controls
- Soft-start Circuitry
-
A new paradigm on the original foundation of audio reproduction – the direct heated triode (DHT). The Allnic A-5000DHT monoblock amplifier has only DHT vacuum tubes in the signal path. What does pure DHT mean for a power amplifier? Silent backgrounds; unmatched clarity, detail, speed, decay and harmonic resolution, immersive and layered sound-staging with incredible air around instruments and voices, “you are there” sound-staging, clarity and presence, accurate natural tone and timbre. Wattage means little, the A-5000 DHT produces unbelievable drive from a single 300B. Simply, like all the 5000 series products, the Allnic A-5000DHT will produce as much faithfulness to the source as the rest of your system can provide.
- 10 watts of high power output
- Direct wired, no circuit boards
- Sophisticated ratio, mixed nickel Permalloy PB cored output transformers
- Analogue power tube current monitoring meters
- Exceptionally easy bias controls
- Soft-start Circuitry
-
The A10000 are 100 watts of pure Class SET power using the KR242 tube developed for the L5000 DHT driving two enormous Kron 1610 output tubes. A very special set of amplifiers, a personal favourite of Mr. Park.
- All stages are operated by pure DHT tubes
- 100W pure Class A, parallel single ended
- All hard wired
- Sophisticated ratio, mixed nickel Permalloy PB cored output transformers
- Low distortion, high output fixed bias
- Easy bias current adjustment
- Analogue power tube current monitor meter
-
We introduced the M-3000 MK2, a monoblock power amplifier in 2016. Using four KT150 as output tubes, which was a new model at the time, M-3000 MKII produced 200W at 8Ω. Above all, the sound was good. It was fast, powerful, detailed, and quiet. Compared to MK1, which produced 140W with the KT120, the clean sound and a transparent stage stood out.
-
The A-2000 MK3 is a class AB power amplifier that uses two KT170 beam-tetrode output tubes per channel and produces 120W in pentode mode and 60W in triode mode through push-pull operation. One triple-connected 5654 pentode tube per channel is used in the first-stage to secure a voltage gain of 26dB, and two 6S4 triode tubes per channel are used as the phase inversion and drive tubes for push-pull driving of the KT170 output tubes. The A-2000 MK3 uses two of Allnic’ssignature permalloy core output transformers, one per channel.
Integrated Amplifiers
-
The T-1500 mk2 stereo amplifier is Allnic Audio’s top of the line 300B SET stereo integrated amplifier model. Like all Allnic Audio products, the T-1500 mk2 has Permalloy (iron and nickel alloy) for its transformer cores. Allnic is grateful to Mr. G.W. Elmen of Western Electric for inventing Permalloy for transformer core use, and in so doing, providing an enormous service to recorded music listeners everywhere.
- 10 watts per channel of pure class A high power output
- Real power drive
- Nickel alloy output transformer
- Self-bias control grid
- Analog power tube current monitoring meters
- Soft-start Circuitry
-
The T-1800 MK2 stereo integrated amplifier is Allnic Audio’s EL34 stereo integrated amplifier model. Like all Allnic Audio products, the T-1800 MK2 has Permalloy (iron and nickel alloy) for its transformer cores. Allnic is grateful to Mr. G.W. Elmen of Western Electric for inventing Permalloy for transformer core use, and in so doing, providing an enormous service to recorded music listeners everywhere.
- 40 watts per channel of push-pull power output
- Remote controlled 41 step silver contact attenuator
- Nickel alloy output transformer
- Self-bias control grid
- Analog power tube current monitoring meters
- Soft-start Circuitry
-
Beauty, grace, and power. Along with amazing, revelatory clarity, incredible dynamics and drive, articulate and powerful bass, and standard setting low noise and distortion, the T-2000 30th Anniversary provides 120 watts per channel of push-pull, pentode power or more than 60 watts SET sounding watts in triode mode; AND pentode/triode switching is “on the fly”. The T-2000 30th Anniversary offers finesse, delicacy and detail with stable, resolute power in the proverbial velvet glove.
- 120 watts of high power output in pentode mode
- More than 60 watts of “SET like” power output in triode mode
- On-the-fly pentode/triode switching
- In-house manufactured, 61 stepped, constant impedance, silver contact attenuator
- Analog power tube current monitoring meters
- Soft-start Circuitry
Analogues
-
Allnic Audio is glad to introduce a new thrilling MC cartridge, Amber, overwhelmingly surpassing the Puritas Ultra. Amber is guaranteed not to displease any LP lovers.
- Cutter head type MC cartridge
- A new rubber damper developed by Allnic
- New CCA (Copper Clad Aluminium) dual coils
- Fritz Gyger S Stylus
- Solid Boron cantilever
-
The H-7000V, Allnic’s wildly popular transformer coupled LCR phono stage, is an upgraded version of the H-3000, the phono stage that won the hearts of hundreds of audiophiles worldwide. The H-7000V differs from the H-7000 in that the H-7000V incorporates LCR Multi-curve Equalization. With the H-7000V, you can play any LP issued before RIAA standardization at its correct equalization level!
- Dual MC step-up transformers
- LCR multi-curve equalization
- All transformer coupled, no coupling capcitors
- Zero negative feedback design
- Equipped with the pure vacuum tubes
- High speed, automatic voltage regulation
-
The HA-5000 is Allnic Audio’s pre-preamplifier, or “Head Amplifier”. It is an active, tube based device for amplification of low voltage signals from moving coil cartridges to allow connection of moving coil cartridges to the moving magnet inputs of a phono-stage, such as the Allnic H-3000 or H-1500. The HA-5000 is an active pre-preamplifier, not a “step-up transformer” like Allnic’s AUT-2000, which uses only a transformer to boost the signal from the cartridge.
- Innovative fixed bias circuit
- Very high S/N ratio
- Extremely wide frequency range
- Ultra flexibility
- Micro-phonic free tube damping know-how
- Variable input load impedances
-
Introducing perhaps world’s finest Direct Heated Triode Phono Stage, the Allnic H-8000 DHT. Built to complement our L-8000 DHT line stage and A-10000 DHT amplifiers, this magnificent 2 piece ultra-high performance multi-input phono stage is sure to “Change the Game”
- Dual MC step-up transformers
- LCR multi-curve equalization
- All transformer coupled, no coupling capcitors
- Zero negative feedback design
- Equipped with the pure vacuum tubes
- High speed, automatic voltage regulation
-
Allnic Audio is glad to introduce a new thrilling MC cartridge, Rose, overwhelmingly surpassing the Puritas . Rose is guaranteed not to displease any LP lovers.
- Cutter head type MC cartridge
- A new rubber damper developed by Allnic Audio
- New CCA (Copper Clad Aluminium) dual coils
- Fritz Gyger 2 Stylus
- Aluminium cantilever
-
Technology continues to evolve, and Allnic Audio’s KS Park’s “out of this world” works of sonic artistry are no exception. The H-5500 replaces the extremely popular H-1202, providing more features and more beauty in both sound and appearance for a relatively small uptick in cost – especially at this introductory price – adding up to an even greater quality to cost ratio than its predecessor. The H-5500 offers:
- dual MM and MC inputs
- Mu-metal shielding to increase SNR
- power supply capacity double that of the H-1202
- current meter for monitoring tube status
- redesigned larger, heavier, and more solid aluminum chassis
-
The H-6500 is basically a vacuum tube phono amplifier with 2 sets of MM and 2 sets of MC inputs, RIAA curve correction through an LCR filter, and a separate power supply unit in a separate chassis. MC boosting is done through a built-in permalloy core step-up transformer with 4 winding ratios, and MM amplification is done through 5842 triodes inserted 4 per channel. MM voltage gain is 40dB, MC voltage gain is 62dB, 66dB, 68dB, 72dB.
-
Allnic is pleased to announce the release of the H-10000 OTL/OCL, its new flagship phono-stage preamplifier. An OTL/OCL (Output Transformer-Less/Output Capacitor-Less) design omits the coupling transformer at the output stage of the vacuum tube amplifier and the capacitor in the signal path, thus reducing distortion, coloration, and energy loss. It is unprecedented for an OTL/OCL circuit to be used in a phono-stage, which requires a level of amplification much higher than that of a line-stage preamplifier.
- OTL/OCL Flagship phono-stage preamplifier
- Equipped with the pure vacuum tubes
- Silver coil MC step-up transformer
- LCR multi-curve equalization
ZL Cables
-
The ZL-8000S is Allnic's first speaker cable which uses silver conductors with existing OFC Conductors. Allnic speaker cables utilize a patented double-bladed spade termination that ensures no loosening for years.
- Silver with OFC conductors
- Zero Loss Technology
- 1000 °C hot melt welding of cable terminations and wire
- Patented double-bladed spade speaker terminations
- Optimum thickness of wire
-
The ZL5000 Power Cable is the Allnic's flagship power cable, equipped with Allnic's patented Zero-Loss Technology.
- Four surface contacts for IEC receptacles, instead of weak line contact
- Heavy gauge nickel plated OFC provides superior high current conductivity
- Double shielding ensures quieter operation
- 1000 °C hot welding between wire and terminal
-
The Mu-7R mk2 Intercable uses Mu-metal as a braided shield, which protects the signal from both kinds of noise. Other audio cable manufacturers tend to use copper or silver shields for signal cables. These are effective only for electric noise, not for magnetic interference.
- Mu-metal braided shield for reducing electromagnetic noise up to max. 98%
- 1000 °C hot melt welding of cable terminations and wire
- Optimum thickness of wire
- MRCT
-
The ZL-5000 is 2.5m speaker cables with ZL Technology, specially designed by Allnic Audio. ZL-5000 speaker cables utilize Allnic's patented double-bladed spade termination that ensures no loosening for years.
- OFC conductors
- 1000 °C hot melt welding of cable terminations and wire
- Allnic's patented, maintenance-free double-bladed terminations
- Optimum thickness of wire
-
The ZL-3000 mk2 is 2.5m speaker cables with ZL Technology, specially designed by Allnic Audio. ZL-5000 speaker cables utilize Allnic's patented double-bladed spade termination that ensures no loosening for years.
- OFC conductors
- 1000 °C hot melt welding of cable terminations and wire
- Allnic's patented, maintenance-free double-bladed terminations
- Optimum thickness of wire
-
The ZL-3000 mk2 Power Cable is the Allnic's first power cable, equipped with Allnic's patented Zero-Loss Technology.
- Heavy gauge nickel plated OFC provides superior high current conductivity
- Four surface contacts for IEC receptacles, instead of weak line contact
- Double shielding ensures quieter operation
- 1000 °C hot welding between wire and terminal
-
The Mu-7R mk2 Digital Intercable uses Mu-metal as a braided shield, which protects the signal from both kinds of noise. Other audio cable manufacturers tend to use copper or silver shields for signal cables. These are effective only for electric noise, not for magnetic interference.
- Mu-metal braided shield for reducing electromagnetic noise up to max. 98%
- 1000 °C hot melt welding of cable terminations and wire
- Optimum thickness of wire
- MRCT
-
The Mu-7R mk2 Phono cable uses Mu-metal as a braided shield, which protects the signal from both kinds of noise. Other audio cable manufacturers tend to use copper or silver shields for signal cables. These are effective only for electric noise, not for magnetic interference.
- Mu-metal braided shield for reducing electromagnetic noise up to max. 98%
- 1000 °C hot melt welding of cable terminations and wire
- Optimum thickness of wire
- MRCT
-
The ZL8000S Power Cable is the Allnic's New flagship power cable, equipped with Allnic's patented Zero-Loss Technology.
- Silver with OFC conductors
- Four surface contacts for IEC receptacles, instead of weak line contact
- Heavy gauge nickel plated OFC provides superior high current conductivity
- Double shielding ensures quieter operation
- 1000 °C hot welding between wire and terminal
-
The Mu-8Rs Interconnect cable uses Mu-metal as a braided shield, which protects the signal from both kinds of noise. Other audio cable manufacturers tend to use copper or silver shields for signal cables. These are effective only for electric noise, not for magnetic interference.
- Silver with OFC conductors
- Mu-metal braided shield for reducing electromagnetic noise up to max. 98%
- 1000 °C hot melt welding of cable terminations and wire
- Optimum thickness of wire
- MRCT
-
The Mu-8Rs Phono cable uses Mu-metal as a braided shield, which protects the signal from both kinds of noise. Other audio cable manufacturers tend to use copper or silver shields for signal cables. These are effective only for electric noise, not for magnetic interference.
- Silver with OFC conductors
- Mu-metal braided shield for reducing electromagnetic noise up to max. 98%
- 1000 °C hot melt welding of cable terminations and wire
- Optimum thickness of wire
- MRCT
-
The Mu-8Rs Digital Interconnect cable uses Mu-metal as a braided shield, which protects the signal from both kinds of noise. Other audio cable manufacturers tend to use copper or silver shields for signal cables. These are effective only for electric noise, not for magnetic interference.
- Silver with OFC conductors
- Mu-metal braided shield for reducing electromagnetic noise up to max. 98%
- 1000 °C hot melt welding of cable terminations and wire
- Optimum thickness of wire
- MRCT
Digital
-
OTL/OCL (Output Transformer-less/Output Capacitor-less) analog output designs to the very best of today’s DAC technology. In common circuits, output capacitors or output transformers are these two coupling devices also introduce their own influences on the transmission of the musical signal, adding their own character (colouration), increasing distortion, and consuming small signals, all as predicted by physical efficiency theory. In addition, they also limit signal dynamics.
- No colouration of the musical signal
- Extremely detailed expression, natural harmonics, and subtle musical decay
- The lowest possible distortion
- The widest musical dynamics
Headphone Amplifiers
-
The HPA- 5000 XL is Allnic Audio’s Output Transformer-Less (OTL) and Output Capacitor Less (OCL) stereo headphone amplifier. The HPA- 5000 XL utilizes a true balanced Positive-Negative cancellation circuit. The HPA- 5000 XL has a voltage gain of +28dB, and a maximum output of 5 watts. Offering stunningly realistic music reproduction, it works best with headphones having an impedance from 30 to 600 ohms.
-
The HPA-3000 GT is Allnic Audio’s output transformer coupled, stereo headphone amplifier. The HPA-3000 GT has a voltage gain of +28dB, and a maximum output of three (3) watts. It works best with headphones having an impedance of from 30 to 600 ohms.
-
-
If you want to experience Allnic Audio’s products,
please contact your local authorized dealers or
Audio Mentors, which is Allnic Audio’s design & marketing company.
